Path & Driveway · 4 min read

Driveway Lighting Ideas for 12V Landscape Systems

Six driveway lighting ideas that work with low-voltage brass fixtures, from path lights along the edge to uplit trees and the entry, with spacing and power tips.

In this guide
    Quick answer

    Light the entrance and every curve first, then line the edges with path lights 8–12 ft apart, staggered side to side. Add well lights or spotlights on trees near the drive so the whole approach glows, not just the edge. Keep everything 12V, warm white and out of the tire line.

    Chapter 01

    Start with what the driver needs

    A driveway is seen from a moving car, at night, often in reverse. Before thinking about looks, make sure three things are visible: the entrance from the street, any curve or change in width, and the edge where pavement meets lawn or a drop. Everything else is decoration.

    “Mark the edges, light the approach, skip the runway.”

    Chapter 02

    Six driveway lighting ideas

    1. Path lights along the edge

    The classic. Place path lights 8–12 ft apart, at least 12 in off the pavement, and stagger them on alternate sides. A straight double row looks like an airport.

    2. Light the entrance pillars or mailbox

    A pair of spotlights or wall lights on the entry columns tells visitors exactly where to turn in, and it is the first thing people see from the street.

    3. Uplight the trees beside the drive

    One or two spotlights per tree gives the drive depth and lights the area around it without adding more fixtures at the edge. See how to uplight trees and palms.

    4. Flush well lights in the lawn

    Well lights sit level with the ground, so cars, mowers and snow plows roll right over the area around them. Use them to graze a wall or a tree trunk near the drive.

    5. Light the garage and the turnaround

    Where the drive widens near the house, wash the garage doors or the facade with a couple of spotlights instead of lining the whole parking area with path lights.

    6. Step lights on retaining walls

    If the drive runs along a wall or has steps up to the front door, brick-size or step lights in the wall light the edge and the path at the same time.

    Chapter 03

    Spacing and placement rules

    Element Rule of thumb
    Path lights along the edge 8–12 ft apart, staggered, 12 in or more from the pavement
    Entrance Always lit, both sides
    Curves A light at the start, the apex and the end of each curve
    Trees near the drive 1–2 spotlights each, 1–3 ft from the trunk
    Color 2700K or 3000K on every fixture

    For walkway-style spacing and a quick fixture count, see How Far Apart Should Path Lights Be?

    Pro tip

    Walk the layout at night with the fixtures on temporary stakes, then drive it. What looks fine on foot can glare straight into a windshield.

    Chapter 04

    Fixtures that survive a driveway

    Fixtures near a drive get hit by sprinklers, salt, mowers and the occasional bumper. Solid brass will not rust or crack in sun and salt, and every Cardon brass fixture carries a lifetime warranty. Keep path lights out of the tire line and use well lights wherever a fixture might get driven over or plowed.

    Chapter 05

    Power a long driveway

    Driveways are long, so wire size and layout matter more than anywhere else in the yard.

    1. Add up the watts of every fixture and multiply by 1.3 to size the transformer.
    2. Split long drives into two or more runs back to the transformer instead of one long chain.
    3. Feed each run from the middle (a “T” connection) so the first and last lights match.
    4. Use 12/2 cable for most driveway runs; check the distances in the wire gauge guide.

    Want the numbers done for you? Use the transformer calculator.

    Questions we hear most

    How far apart should driveway lights be?

    About 8–12 ft apart, staggered on alternate sides, and at least 12 in back from the pavement.

    Should driveway lights be on both sides?

    Light both sides at the entrance and on curves. Along straight sections, staggering lights on alternate sides looks better than matching pairs.

    What are the best lights for a driveway?

    Low-voltage path lights along the edges, well lights where fixtures might be driven over, and spotlights on nearby trees or entry pillars.

    Can I use low voltage lights for a long driveway?

    Yes. Split the lights into several runs, feed each run from the middle, and use 12/2 cable so voltage drop stays under control.

    How many lights do I need for my driveway?

    Divide the driveway length by 10 ft for one side, then add lights for the entrance and each curve. A 100 ft drive usually needs about 10–14 path lights, staggered.

    Plan your system

    Power your lights

    Size the transformer at your total watts × 1.3, and use 12/2 wire on longer runs.

    Shop the guide

    All path lights ›

    Need help planning your lighting?

    Send us a photo or call. We’ll tell you exactly what to buy.

    Call 949-381-5333

    Keep reading